ASME A112.19.3-2000 pdf download – Stainless Steel Plumbing Fixtures (Designed for Residential Use)
ASME A112.19.3-2000 pdf download – Stainless Steel Plumbing Fixtures (Designed for Residential Use). 2.4 Dimensions and Tolerances Fixtures shall conform to tile applicable dimensions and tolerances given herein. Where not otherwise indicated, a tolerance of plus or minus 1% shall apply. Maximum and minimum dimensions...
ASME B30.19-2000 pdf download – CABLEWAYS
ASME B30.19-2000 pdf download – CABLEWAYS. Section 19-0.1: Scope of B30.19 within the generai scope defined in Section i of theIntroduction,the scope of B30.19 applies to all load transporting. hoisting, and iowering cabie-supported sys-tems operating on and supported from track cable(s). This Siandard does not...
ASME A112.18.6-2009 pdf download – Flexible water connectors
ASME A112.18.6-2009 pdf download – Flexible water connectors. 4.1.3 Copper alloy components shall contain at least 56% copper. 4.1.4 Stainless steel components in contact with water shall be made from 300 or 400 series stainless steel. Ferrous steel parts not in contact with water shall...
ASME B16.10-2009 pdf download – Face-to-Faceand End-to-End Dimensions of Valves
ASME B16.10-2009 pdf download – Face-to-Faceand End-to-End Dimensions of Valves. 2.3.3 End-to-End. For those flanged valves where the gasket contact surfaces are not located at the extreme ends of the valve, the distance between the extreme ends is described as the end-to-end dimension and applies...
ASME B16.36-2015 pdf download – Orifice Flanges
ASME B16.36-2015 pdf download – Orifice Flanges. This requires that an observed or calculated value be rounded off to the nearest unit in the last right-hand digit used for expressing the limit. Decimal values and tolerances do not imply a particular method of measurement. 2.5...
ASME B16.33-2012 pdf download – Manually Operated Metallic Gas Valves forUse in Gas Piping Systems Up to 175 psi(Sizes NPS 1/2 Through NPS 2)
ASME B16.33-2012 pdf download – Manually Operated Metallic Gas Valves forUse in Gas Piping Systems Up to 175 psi(Sizes NPS 1/2 Through NPS 2). (b) Tensile tests shall be conducted on six dumbbells in accordance with ASTM D412. Three of the tensile tests shall be...
ASME B16.25-2012 pdf download – Buttwelding Ends
ASME B16.25-2012 pdf download – Buttwelding Ends. 1.5 Referenced Standards Standards and specifications adopted by reference in this Standard are shown in Mandatory Appendix II. It is not considered practical to identify the specific edition of each standard and specification in the individual references. Instead,...
ASME B16.21-2011 pdf download – Nonmetallic Flat Gaskets for Pipe Flanges
ASME B16.21-2011 pdf download – Nonmetallic Flat Gaskets for Pipe Flanges. 2.6 Size NPS, followed by a dimensionless number, is the designation for nominal pipe size, as described in ASME B36.1OM and is related to the reference nominal diameter, DN, used in international standards. The...
ASME B16.20-2012 pdf download – Metallic Gaskets for Pipe Flanges Ring-Joint, Spiral-Wound,and Jacketed
ASME B16.20-2012 pdf download – Metallic Gaskets for Pipe Flanges Ring-Joint, Spiral-Wound,and Jacketed. 5.2 Dimensions and Tolerances 5.2.1 General. Dimensions and tolerances for grooved nwtal gaskets with covering layers and centering rings shall be in accordance with Fig. 3 and Tables 26 through 28 (Tables...
ASME B16.18-2012 pdf download – Cast Copper Alloy Solder Joint Pressure Fittings
ASME B16.18-2012 pdf download – Cast Copper Alloy Solder Joint Pressure Fittings. The largest opening in the fitting governs the tolerance to be applied to all openings. Tables 3 through 19 and Tables 1-3 through 1-19 offer dimensions for pressure fittings covered by this Standard....